Reprogram on bench the Magneti Marelli ECU MM10JA and IAW 11GF equipped on some models of the FCA group.
Work both in BENCH and BOOT modes to fully meet your customers’ needs.
Alientech
February 14, 2024
K-SUITE – RELEASE 4.55
New K-TAG protocols to work in Boot and Service Mode with ECU Bosch equipped on many Link &Co, Mercedes-Benz, Nissan, Renault, and Volvo vehicles. The ECUS Bosch involved are:
These are vehicles such as the new Volvo XC40, but also vehicles like 2003 Mercedes ML-Class and Volvo S80 in production from 2001 to 2006. Depending on the intervention you have to perform, you can choose the best way, because surely you have the right tool in your hands!
New K-TAG Protocol
Read and write in Service Mode
| Nv300 | 1.6 dCi 120 6MT | Diesel | 88 Kw |
Read and write in Service Mode
| Trafic | 1.6 dCi 120 6MT | Diesel | 88 Kw |
New K-TAG Protocol
Read, write and clone in Boot Mode
| S80 | 2.4 20v D | Diesel | 96 Kw |
| S80 | 2.4 20v D5 | Diesel | 120 Kw |
New K-TAG Protocol
Read, write and clone in Boot Mode
| ML-Class | 430 V8 5AT | Petrol | 200 Kw |
New K-TAG Protocol
Read and write in Service Mode
| XC40 | 1.5 T3 | Petrol | 115 Kw |
| XC40 | 1.5 T3 | Petrol | 120 Kw |
Read and write in Service Mode
| 01 | 1.5 PHEV | Petrol | 192 Kw |
| 01 | 2.0T | Petrol | 140 Kw |
| 02 | Drive-E 1.5 TD | Petrol | 132 Kw |
| 02 | Drive-E 2.0 TD | Petrol | 140 Kw |
| 03 | 1.5 TD | Petrol | 132 Kw |
Boot Mode modality. Read, write, and clone for deep interventions and repairs.
It allows you to reach the hearth of the ECU and TCU to read and write microprocessor, EEPROM and flash memory. With K-TAG it is also possible to make advanced changes, backup operations and “cloning” of the ECU.
Mercedes ML-Class equipped with Bosch ME2.1 and Volvo S80 with ECU Bosch EDC15C11 are vehicles in circulation from the first years of 2000 and can have issues, even complex ones, but certainly resolvable thanks to the new K-TAG protocols.
Rely on a complete, reliable tool that guarantees results.
Service Mode. Remap at best without opening the ECU and recalibrate with ECM Titanium!
You work on Nissan NV300 and Renault Trafic of 2017 equipped with ECU Bosch DCU17PC42 and Volvo XC40 and Lvnk & Co 01, 02 and 03 equipped with Bosch MG1CS080.
Commercial vehicles and brand-new cars, that you are able to remap depending on your customer’s needs.
With the ECU MG1CS080 remapping you can calibrate all the basic parameters for the engine functioning: turbo pressure, injection, ignition timing and wastegate opening.
In addition, it is also possible to unlock the true performance of the low-powered versions: this power reduction is controlled by the maximum torque limiters and with ECM drivers it is possible to remove this limitation.
Work both in BENCH and BOOT modes to fully meet your customers’ needs.
Intervene on the electronic management of robotized transmissions equipped on Renault Master III and some vehicles of the FCA group.
Even more possibilities for modification and customization are available for Porsche brand vehicles.
Enhance performance and reduce fuel consumption on the latest supported vehicles.
Reprogram without risks and increase your earning possibilities.
Act swiftly and effectively to optimize performance on the newly supported vehicles.
